Newest V4.94 Digiprog III Digiprog3 Odometer Master Programmer Entire Kit


digiprog3-v4.94-vehicle-list.pdf  (58K)

Carsets.co.uk provides Digiprog 3 V4.94 odometer correction tool several packages that meet various demands. 
Following is the full DigiProg km tool composition table which will lead you to a better choice.






Digiprog III 4.94 successful test

1)For VW, Audi, Skoda vehicles:

Passat 2007 —> OBD OK
passat 2011 work obd 5 min
passat 2012 work obd
passat cc 2012 work obd
Passat 2011 menu dash diag -2012 read ok/write ok /3 minute.
passat 2006 dash work
passat 2011 work by OBD

Tiguan 2007 —> OBD OK
tiguan 2009: ok test Many Time always ok
Tiguan 2011 OBD no problem, takes about 10 minutes

Jetta 2013 take golf 6 on car list. Work fine 2 minutes
jetta 2012 work obd
jetta 2014: ok test Many Time always ok

Skoda Superb (3t) II 2009y only by obd less then 5min
Skoda Roomster 2009 —> Diag work Perfect
Skoda octavia 2009 1.9tdi instrument ok, ecu ok, dsg reset ok
SKODA Fabia 2009 obd ok. fabia -diag-read ?-write ok. (digi4.94)
skoda superb 2011 nec+24c64 obd works fine.

audi a4 2010 obd ok, audi a3 2010 obd ok
A6, 2009 work OBD, 4-5 minute.
no problem with audi a3 for now 2011 and 2010 doing ok by obd

Volkswagen Eos obd2 ——ok
vw eos 2007 —> Diag obd2 work

Golf 6 2012 obd ok
golf 2007: dash and dsg ok
golf mk5..ok
Golf 4 MM Just open dash en look voor 24C** it takes 2 minutes

300 m 2009 ok
wrangler 2012 ok
VW evoque 2012 work by OBD
Seat MII 2013 —> OBD Work

2)For BMW vehicles:
BMW E46 2004 —> 35080 Clip Work

3)For Ford vehicles:
Ford Fiesta 2012 —> OBD OK
Ford Fiesta HCS12 —> ST48 Work
2012 Ford Focus – 95320 – by ST1 work ok

4)For Mitsubishi:
For read & write correct Mileage use
Mitsubishi Outlander 93C86 V2 —> Work Perfect on Peugeot 4007 2012

5)For Mercedes Benz:
w211 2005 dash via st60 read ok/write ok/ezs sync blocked ok.
E39 m5 dash done with digi using st47
MERCEDES w210 E – DB 4_99 with Stecker 10 , ok!

6)For Opel:
-Opel Vivaro 2013 —> EEPROM Clip work 93c76
-Astra J 2011 work by OBD.
-Opel Insignia 2014 —> OBD Work perfect

7)For Fiat:
Fiat Grande Punto EVO 2011 dash– obd OK…. fiat doblo
Fiat Ducato 2012 work perfect OBD
Fiat Doblo 2009 —> OBD Work perfect 1 sec. Job

8)Other models:

Galaxy 2008 new model by the OBD ok
Successfully made chevrolet orlando like a opel insignia

Digiprog read/write 35080 for 100%.

Range Rover Evoque 2013 via obd ok

Nissans: 2002 Altima 93C66 OK in circuit with Murano; 2001 Xterra 93c56 OK unsolder with Patrol

Toyota RAV 4 2007 —> eeprom clip 93c56 work

– Made : sportage 2012
Swift 2014
Ranger 2010
Prado 2006
Runner 2006
Navarra 2012

All eeprom on board …i did NOT try obd
– salvage Yard
nitro 2009 ok
patriot 2013 ok
2015 xtrail does work with digiprog 4.94, chip 93c86 worked a treat
volvo s80 2008+ work good 10min.

Digiprog V4.94 cannot work on some
Digi can not do some Golf 6 and Polo Dash by obd.
Digi can do only VDO dash Golf 6 by obd, not Magneti Marelli.
A3 sportback 2009. killed
Focus 2011 not work


Digiprog3 V4.94 Update Note:
 
1. Make sure the power connect is ok and the power supply is enough and stable. 

make-sure-the-power-connect-is-ok
 
2. Donot enter standby mode, or the computer screen display as in protection state.
3. Donot cut off the power during the digiprog3 update process.
4. Operation Windows System must be Winxp sp3 32bit, close the antivirus and firewall software in advance. 
5. Make sure the device serial number match with the sn of the Digiprog Update file, and check if there are Digi1.bin and Digi2.bin in the update file before start.

make-sure-digiprog3-serial-number-match-the-digiprog-update-file

6. Make sure select the Digi1.bin file during update process.


How to update Digiprog3 V4.94 ?

 
1. Connect the USB cable to the computer, start your dp3, run Digiloader1.exe.

digiprog3-4_94-update-notice

connect-usb-cable-to-the-computer-2

connect-usb-cable-to-the-computer-4

 
2. Choose the right port, select Digi1.bin, Click the button. If your dp3 dose not enter blue screen,check your setting and restart from step 1.

digiprog3-4_94-update-notice-select-digi1bin-file

digiprog3-4_94-update-display-bluescreen
 
3. In upgrading, it should be like this until over.  Attention, it will be damaged if you remove it now.
 
4. Upgrade Over. Your dp3 should restart automatically.

digiprog3-update-ok-to-restart